LUBRIFICATION SYSTEM PRODUCTA

SILICONE OIL  100%

Lubrication with 100% silicone oil avoids the unpleasant inconvenience of any spillage going to ruin the coils and the cartoons causing quality problems on the seals.

LUBRIFICATION A CLOUD SYSTEM 

homogeneous lubrication over the entire surface of the gasket;
– Absence of dispersion and drying of the gasket;
– Lasting lubrication for more than 6 months from production.

FAST AND EASY MOUNTING
the presence of a stable and constant lubrication over the entire surface of the gasket ensures a fast and easy mounting with clear reductions in time and costs of the frame realization.

FAST AND EASY INSTALLATION 
the RAPID® system designed by Producta allows to have a series of regular micro-cuts on the entire surface of the gasket so that granting to the installer the possibility to install the profile along all the perimeter in a fast and easy way.

MAXIMUM SEAL AND ZERO RITREAT 
the presence of micro-cut avoids, during the installation, difficult and dangerous cut and joint on corners that can often compromise the seal performance of the gasket owing to retreats and bad adherences.

MAXIMUM PRODUCTIVITY AND MINIMUM COST OF LABOUR
it has been calculated that the total exclusion of the cut and joint’s phase during the mounting of the gasket permits to increase the productivity per hour than 40% so that reducing of 30% the labours cost’s incidence.

PROTECTIVE FILM ON THERMAL BREAK BARS

DESCRIPTION
The Producta 1020 protective film is a dark green self-adhesive tape developed from heat-resistant material. It can be used for a large range of application where resistance to high temperatures is specifically required, along with protection of the original product characteristics from prolonged exposure to atmospheric agents.

PHYSUCAL PROPERTIES AND CHARACTERISTICS

Adhesion to surface 3,6 N/cm ASTM D-3330
Resistance to traction 84,0 N/cm ASTM D-3759
Elongation at break 83% ASTM D-3759
Support thickness 0,05 mm ASTM D-3652
Totale thickness 0,08 mm ASTM D-3652
Operating temperature Up to 204 °C

SPECIFIC APPLICATIONS

Mask for powder finishes
Elimination of bubbles during finish
Protection and storage of product from atmosferic agents

The partnership with qualified companies along with Producta’s constant orientation to technological innovation aimed at solving all technical problems linked to the use of polyamide bars for thermal break, have resulted in the development of a high performance product.

The adhesive film is applied to the polyamide bar surface by means of a high precision automatic system patented by our research and develpment department. Thanks to this innovation, we have made the following improvements to our products:

MASK FOR POWDER FINISHES

THE DEFINITIVE SOLUTION TO THE PROBLEM OF NON-UNIFORM FINISHES AND THE PHENOMENON OF MARKS AND PIECING

The protective film applied to the visible surface of the bar garantees total surface protection from the pigmented powders during the finishing stage, thanks to its resistance to high temperatures.

OPERATING TEMPERATURE : Up to 204°C

After finishing, the film can be easily removed, leaving the black bar surface perfectly smooth and polished.

PROTECTION AGAINST BUBBLE FORMATION

SOLVES THE PROBLEM OF THE FORMATION FO SURFACE BUBBLES DURING THE FINISHING STAGE OF THE COUPLED PROFILE

If the polyamide bar has absorbed humidity during storage, this is released during the nishing stage where temperatures in excess of 180°C are reached. This passage of state involves an increase in volume that can be seen in the formation of bubbles beneath the nish covering the bar. The application of the protective film guarantees perfect bar protection against the absorption of humidity during storage.

This allows for the following:
MAXIMUM REDUCTION OF HUMIDITY ABSORPTION guaranteeing an excellent finish and consequently eliminating the problem of surface bubbles;

IMPROVEMENT IN SYSTEM SEAL PERFORMANCE as a perfect adhesion is guaranteed that can otherwise be compromised by a rough nish surface on the bar.

PROTECTION AGAINST ATMOSPHERIC AGENTS

Always in compliance with the recommendations given on storage, the application of a protective film guarantees better protection from atmospheric agents and better preservation of the technical-dimensional characteristics of the extruded product.

As part of the innovative technical solutions Producta has introduced a new package in the already wide range of available packaging

The new packaging, patented together with Alutec, thanks to its small dimensions (39x39x15,5 cm) allows a highly comfortable storage and is in accordance with the needs of customers.

Thanks to the central hole, the user can remove the seal without removing the coil from the package, which allows the product to remain always protected, clean and ready for use